Re: Data I/O 29B to PC cable?

From: Arcadeforever <arcadeforever_at_gmail.com>
Date: Fri Nov 30 2007 - 11:08:47 EST

Wow, that sound like a real pain I definately dont do that, you are doing
the same thing I am, except I use win 98SE, but yes null modem cable, unit
set to remote( I forget the dipswitch settings) it all should work fine, one
piece of advice though, make sure you dont have any (Blackberry, palm pilot)
software using the serial port that will muck it up for sure.
Wayne

On Nov 30, 2007 10:49 AM, Andy Welburn <warlords@punkass.com> wrote:

> I use my workshop pc (a P3-800) with the modified version, using a null
> modem cable i think? its not a special modified cable, just something off
> the shelf.
>
> I run windows XP, file system is FAT32, dunno if that makes any
> difference?
>
> but.... here's the thing... The only way it works for me is if i switch
> the
> programmer on, wait for it to finish its self test... it'll say 'remote
> mode' then i have 30 seconds to load up the promlink software, and perform
> an action, any action that has to talk to the programmer, like 'process'
> or
> 'fill ram from master'.
>
> It seems that if i don't do that, the programmer times out and the com
> port
> gets 'stuck' and i have to reboot, there's no way of clearing it. Also
> power
> cycling the 29b just goes through the self-test then instead of going to
> remote mode reports somethgin like 'i/o error 33' which can be cleared by
> disconnecting the serial cable and power cycling, then re-attatching the
> serial cable, but it'll crash again with the i/o error if you havn't
> rebooted the pc :-)
>
> Thing is, the action i have to do doesn't need to do anything, and you
> don't
> need to actually perform it, it just has to send something to the
> programmer
> to tell it which socket to use, once its done that, it never times out and
> i
> never have any problems with it.
>
> Also, never switch the 29b on with a blank PROM in any of the sockets, it
> will bugger them up.
>
> Am i the only one that has to work with it like that? I don't mind really,
> its been rock solid for the 8 years I've owned it, this particular pc/OS
> configuration hasn't changed for at least 5 years i'd say... it works
> perfectly otherwise.
>
> Andy
>
> ----- Original Message -----
> From: "Joe Magiera" <joemagiera@ameritech.net>
> To: "'Technical Tools Mail List'" <techtoolslist@flippers.com>
> Sent: Tuesday, November 27, 2007 3:19 PM
> Subject: [Techtoolslist] Data I/O 29B to PC cable?
>
>
> > Modified the subject to be more accurate...
> >
> > Martin, thanks much for that info.
> >
> > Ok, can anyone else confirm that they use a cable/connection as shown in
> > the
> > link below, or have they been able to use a standard serial 25 pin cable
> > on
> > both sides (Data I/O and PC)? Thanks,
> >
> > Joe
>
> [snip]
>
>
> _______________________________________________
> Techtoolslist mailing list
> Techtoolslist@flippers.com
> http://seven.pairlist.net/mailman/listinfo/techtoolslist
>

-- 
Wayne Moore
_______________________________________________
Techtoolslist mailing list
Techtoolslist@flippers.com
http://seven.pairlist.net/mailman/listinfo/techtoolslist
Received on Fri Nov 30 11:18:19 2007

This archive was generated by hypermail 2.1.8 : Fri Nov 30 2007 - 11:50:00 EST