Re: Re: RF Shields for WG6102 HV Cages

From: tom mcclintock <tomm_at_mgcap.com>
Date: Wed Jun 19 2002 - 16:13:49 EDT

That is exactly correct. Two edges are folded, one fold down the center
and a hole punched for the connector to the deflection board.

Rodger Boots wrote:
>
> Aren't these made of perforated aluminum? I have access to that in bulk
> at my Real Job.
>
> Jon Raiford wrote:
> >
> > I should have one I can rip out of a game. If we make these, should we make them for the G05 and V2000 as well? I have a couple of those shields as well that I could send.
> >
> > Jon
> >
> > At 02:27 PM 6/19/2002 -0500, you wrote:
> > >Does anyone have one that can be borrowed for use as a template in
> > >making more?
> > >
> > >
> > >Jon Raiford wrote:
> > >>
> > >> The shields for the HV cages are basically impossible to find. We should really come up with a good replacement. I'd buy 10 if I could.
> > >>
> > >> Jon
> > >>
> > >> At 06:48 PM 6/19/2002 +0100, you wrote:
> > >> >At 05:39 pm 19 06 02, you wrote:
> > >> >>Sounds like you don't have the cover on the HV cage. I removed one of mine for a short time to help that section run cooler. It did run cooler but the noise radiated made the lines look "noisy". Stuffed it back on and the pix was stable again.
> > >> >
> > >> >My tempest has been doing this for a while and has no cage,
> > >> >
> > >> >I'll repeat my earlier request ... has anyone got a cage from a dead HV unit that they sell/donate to me?
> > >> >
> > >> >
> > >> >
> > >> >Dave Langley
> > >> >www.robotron-2084.co.uk
> > >> >
> > >> >---------------------------------------------------------------------------
> > >> >** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
> > >> >** message body to vectorlist-request@synthcom.com. Please direct other
> > >> >** questions, comments, or problems to vectorlist-owner@synthcom.com.
> > >>
> > >> ---------------------------------------------------------------------------
> > >> ** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
> > >> ** message body to vectorlist-request@synthcom.com. Please direct other
> > >> ** questions, comments, or problems to vectorlist-owner@synthcom.com.
> > >
> > >---------------------------------------------------------------------------
> > >** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
> > >** message body to vectorlist-request@synthcom.com. Please direct other
> > >** questions, comments, or problems to vectorlist-owner@synthcom.com.
> >
> > ---------------------------------------------------------------------------
> > ** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
> > ** message body to vectorlist-request@synthcom.com. Please direct other
> > ** questions, comments, or problems to vectorlist-owner@synthcom.com.
>
> ---------------------------------------------------------------------------
> ** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
> ** message body to vectorlist-request@synthcom.com. Please direct other
> ** questions, comments, or problems to vectorlist-owner@synthcom.com.
---------------------------------------------------------------------------
** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
** message body to vectorlist-request@synthcom.com. Please direct other
** questions, comments, or problems to vectorlist-owner@synthcom.com.
Received on Wed Jun 19 13:18:48 2002

This archive was generated by hypermail 2.1.8 : Fri Aug 01 2003 - 00:33:29 EDT