Re: My Red is dead!

Maybe HRDiemen can be persuaded to make some up...?

I read on their website that if you need a lopt that is not listed in their
equavalent part number list, they will issue a new part number and make a
new batch provided that they are supplied with a good working unit.... Might
be something to look at in a couple of years time ? I would expect that
they would be cheaper too..

Cheers, Colin

----- Original Message -----
From: simon hanlon <simonjhanlon@btopenworld.com>
To: <vectorlist@vectorlist.org>
Sent: Wednesday, March 08, 2006 9:33 PM
Subject: Re: VECTOR: My Red is dead!

> No I didn't order any, I did know it was dead but it really kills me to
pay
> so much for a £20 transformer, its such a rip! I am going to make do with
> one from a 6100, some glue and a little magic. Actually I will leave the
> magic to my old man as I'm sure he will find a way around it. I'll let you
> know how I get on....If I'm still alive that is!
> I think the Amp deflection board is Ok but the HV units suck
> ----- Original Message -----
> From: "Alpha1" <lists@arcadeoll.com>
> To: <vectorlist@vectorlist.org>
> Sent: Wednesday, March 08, 2006 9:14 PM
> Subject: Re: VECTOR: My Red is dead!
>
>
> >I have 4 Wintrons on order.
> >
> > Didn't you order any when you had the chance??! You knew you had a RiD
and
> > you knew this day would come!!
> >
> > Oliver
> >
> >
> > ----- Original Message -----
> > From: "simon hanlon" <simonjhanlon@btopenworld.com>
> > To: <vectorlist@vectorlist.org>
> > Sent: Wednesday, March 08, 2006 8:32 PM
> > Subject: Re: VECTOR: My Red is dead!
> >
> >
> >> Actually I meant a replacement for sale not another Red!
> >> ----- Original Message -----
> >> From: "simon hanlon" <simonjhanlon@btopenworld.com>
> >> To: <vectorlist@vectorlist.org>
> >> Sent: Wednesday, March 08, 2006 8:09 PM
> >> Subject: VECTOR: My Red is dead!
> >>
> >>
> >>> Anyone have one for sale/trade?
> >>> I have the old red one out of circuit and was wondering if anyone
knows
> >>> what pin 2 is for. As far as I can tell pins 1 and 9 are primary. 4
and
> >>> 8 b+, 6,7 Ground and Heater voltage appears to come from a bit of wire
> >>> wrapped around the core and tied to ground with a .3 ohm resistor.
When
> >>> I try the Transformer in circuit the 50 ohm resistor across vr2 starts
> >>> to smoke, with my meter between the bu406d and pin 1 of the HV
> >>> transformer I'm getting 1.1Amps...this doesn't seem to be a lot or is
> >>> it?
> >>>
>
>>> ------------------------------------------------------------------------

---
> >>> ** Unsubscribe, subscribe, or view the archives at
> >>> http://www.vectorlist.org
> >>> ** Please direct other questions, comments, or problems to
> >>> chris@westnet.com
> >>
> >>
>
>> -------------------------------------------------------------------------
--
> >> ** Unsubscribe, subscribe, or view the archives at
> >> http://www.vectorlist.org
> >> ** Please direct other questions, comments, or problems to
> >> chris@westnet.com
> >>
> >
>
> --------------------------------------------------------------------------
-
> > ** Unsubscribe, subscribe, or view the archives at
> > http://www.vectorlist.org
> > ** Please direct other questions, comments, or problems to
> > chris@westnet.com
>
>
> --------------------------------------------------------------------------
-
> ** Unsubscribe, subscribe, or view the archives at
http://www.vectorlist.org
> ** Please direct other questions, comments, or problems to
chris@westnet.com
---------------------------------------------------------------------------
** Unsubscribe, subscribe, or view the archives at http://www.vectorlist.org
** Please direct other questions, comments, or problems to chris@westnet.com