Re: WG6100 issue

Well, that's worth a try...thanks.

Op 16 apr 2009, om 20:39 heeft andre het volgende geschreven:

>
> I had one that had the non-inductive look to some extent that was
> solved by removing the green box capacitors.. Not sure if it was one
> or both though.
>
> --- On Tue, 4/14/09, Andre Huijts <a.huijts@upcmail.nl> wrote:
>
>> From: Andre Huijts <a.huijts@upcmail.nl>
>> Subject: Re: VECTOR: WG6100 issue
>> To: vectorlist@vectorlist.org
>> Received: Tuesday, April 14, 2009, 1:47 AM
>> Thanks, the text on the
>> resistors says: RGN10 1.5 OhmsJ and next line NOBLE 17. It
>> looks as if those are the original one's. Can't find
>> anything on google with this info....maybe some 6100 can
>> verify these are original or not ?
>> Here's a picture of the deflection board
>> before I started working on it (and cleaned
>> it):web.jpg
>>
>> Thanks, André
>>
>> Op 13 apr 2009, om 23:23 heeft Scott Swazey het
>> volgende geschreven:
>> IIRC, Some of the parts were stamped
>> "NI". Just read the part number off the
>> resistor and look it up on Google.
>>
>> -Scott
>>
>>
>> At 02:11 PM 4/13/2009, Andre Huijts wrote:
>> That is a brilliant hint, thanks !
>>
>> Stupid from me as
>> I've read about this before but thought it was
>> Amplifone only....
>>
>> Gonna check it out.
>> Anyway I can recognize if they're non-inductive or
>> not ?
>>
>> Thanks !
>>
>> Op 13 apr 2009, om
>> 22:43 heeft Scott Swazey het volgende geschreven:
>>
>>> Check the two big
>> 10W resistors. It should be a non-inductive part.
>>>
>>> -Scott
>>>
>>> At 10:58 AM
>> 4/13/2009, you wrote:
>>>> I'm
>> working on this WG6100 where some vectors (esp. on the
>> letters)
>>>> seem to be
>> badly drawn.
>>>>
>>>> Check out
>> this very short video:
>>>>
>>>> http://www.youtube.com/watch?v=_pmbmheq7Gg
>>>>
>>>> Note the W
>> and the other letters don't look as nice as on my
>>>> Amplifone.
>>>>
>>>> The PCB set
>> is normally running in my cockpit and working fine on my
>>>> 25"
>> Amplifone so it's not a PCB issue.
>>>> The WG6100
>> has a LV2000 installed, cap-kit and redone all solderings
>>>> on deflection
>> and neck pcb.
>>>> LV2000
>> voltages are exactly set at 26.00V and -26.00V
>>>> As mentioned
>> PCB set works fine, BIP is correctly set-up.
>>>>
>>>> Is this
>> because of WG's lower slew-rate or can something be done
>> to
>>>> correct this
>> ?
>>>>
>>>> Thanks.
>>>>
>> ---------------------------------------------------------------------------
>>>> **
>> Unsubscribe, subscribe, or view the archives at http://www.vectorlist.org
>>>> ** Please
>> direct other questions, comments, or problems to chris@westnet.com
>>>
>>>
>> ---------------------------------------------------------------------------
>>> ** Unsubscribe,
>> subscribe, or view the archives at http://www.vectorlist.org
>>> ** Please direct
>> other questions, comments, or problems to chris@westnet.com
>>
>> André Huijts
>> andre.huijts@upcmail.nl
>>
>>
>>
>>
>>
>> ---------------------------------------------------------------------------
>> ** Unsubscribe,
>> subscribe, or view the archives at http://www.vectorlist.org
>> ** Please direct other
>> questions, comments, or problems to chris@westnet.com
>>
>> ---------------------------------------------------------------------------
>> ** Unsubscribe, subscribe, or view the archives at http://www.vectorlist.org
>> ** Please direct other questions, comments, or problems to
>> chris@westnet.com
>>
>> André
>> Huijtsandre.huijts@upcmail.nl
>>
>>
>>
>>
>>
>
>
>
> __________________________________________________________________
> Be smarter than spam. See how smart SpamGuard is at giving junk
> email the boot with the All-new Yahoo! Mail. Click on Options in
> Mail and switch to New Mail today or register for free at http://mail.yahoo.ca
> ---------------------------------------------------------------------------
> ** Unsubscribe, subscribe, or view the archives at http://www.vectorlist.org
> ** Please direct other questions, comments, or problems to chris@westnet.com

André Huijts
andre.huijts@upcmail.nl

---------------------------------------------------------------------------
** Unsubscribe, subscribe, or view the archives at http://www.vectorlist.org
** Please direct other questions, comments, or problems to chris@westnet.com
Received on Fri Apr 17 12:12:57 2009