RE: G08_105 manual RE: Schematics

Yes mine is different, the one I have is the issued by Electrohome and is
specific to the G08_105. I'll get it scanned and off to Tom M. and Al K for
posting. I'll send it to Mike Haaland too. I should get this done next
week some time.

Joe

> -----Original Message-----
> From: owner-vectorlist@synthcom.com
> [mailto:owner-vectorlist@synthcom.com]On Behalf Of Joe
> Sent: Friday, April 04, 2003 6:50 PM
> To: vectorlist@synthcom.com
> Subject: RE: G08_105 manual RE: VECTOR: Schematics
>
>
> I have this manual:
>
> www.joesarcade.com/schematic1/monitor/electrohome/g08.pdf
>
> Is yours a bit different?
>
> -----Original Message-----
> From: Joe Magiera [mailto:joemagiera@ameritech.net]
> Sent: Friday, April 04, 2003 3:00 PM
> To: vectorlist@synthcom.com
> Subject: G08_105 manual RE: VECTOR: Schematics
>
> I'm sorry, I hadn't realized people had been looking for this manual. I
> have a buddy about 5 minutes away with a good scanner. I will ask him
> to
> scan it. I don't have a place to host it though. It's not a large
> manual
> (11 pages). Will Al Kossow still take/make updates to Spies? Or does
> anyone else have a good place to host it?
>
> Joe
>
> > -----Original Message-----
> > From: owner-vectorlist@synthcom.com
> > [mailto:owner-vectorlist@synthcom.com]On Behalf Of Joe Magiera
> > Sent: Friday, April 04, 2003 2:35 PM
> > To: vectorlist@synthcom.com
> > Subject: RE: VECTOR: Schematics
> >
> > It is the typical yellow cover Electrohome manual. It does not
> > specifically
> > have a parts list, but the last schematic does list the specific part
> (the
> > component layouts only list a part number). The title and table
> > of contents
> > are:
> >
> > SERVICE AND OPERATION MANUAL G08-105 X-Y COLOUR MONITOR (November,
> 1982)
> >
> > G08-105 Model
> > Service Date Reference
> > Warnings
> > Operating Instructions
> > Performance and Operating Data
> > Product Safety and Guidelines
> > Service Set-Up Procedure
> > CRT P.C.B. Component Layout
> > EHT P.C.B. Component Layout
> > X-Y P.C.B. Component Layout
> > Notes
> > Schematic
> >
> > Joe
> > joemagiera@ameritech.net
> >
> > > -----Original Message-----
> > > From: owner-vectorlist@synthcom.com
> > > [mailto:owner-vectorlist@synthcom.com]On Behalf Of Mark Jenison
> > > Sent: Friday, April 04, 2003 1:11 PM
> > > To: vectorlist@synthcom.com
> > > Subject: Re: VECTOR: Schematics
> > >
> > >
> > > Does it contain schematics and parts lists? If so, that'd save
> > > me a lot of
> > > time :-)
> > >
> > > ----- Original Message -----
> > > From: "Joe Magiera" <joemagiera@ameritech.net>
> > > To: <vectorlist@synthcom.com>
> > > Sent: Friday, April 04, 2003 2:49 PM
> > > Subject: RE: VECTOR: Schematics
> > >
> > >
> > > > Are you looking to create a G08_105 manual? I have that manual
> > > and I'd be
> > > > glad to loan it to you if you'd like to borrow it.
> > > >
> > > > Joe
> > > > joemagiera@ameritech.net
> > > >
> > > > > -----Original Message-----
> > > > > From: owner-vectorlist@synthcom.com
> > > > > [mailto:owner-vectorlist@synthcom.com]On Behalf Of Mark Jenison
> > > > > Sent: Friday, April 04, 2003 11:40 AM
> > > > > To: vectorlist@synthcom.com
> > > > > Subject: VECTOR: Schematics
> > > > >
> > > > > Hi all,
> > > > >
> > > > > I'm considering redrawing an updated set of schematics for the
> > > > > G08 monitor,
> > > > > and eventually using it as a base for entering the G08-105
> > > > > schematics. Does
> > > > > anyone have a recommended schematics drawing package for
> > > something like
> > > > > this? I'd prefer a freeware package if possible. Is there a
> > > recommended
> > > > > format for schematics? Thanks.
> > > > >
> > > > > --
> > > > > Mark Jenison
> > > > >
> > > > >
> ------------------------------------------------------------------
> > > > > ---------
> > > > > ** To UNSUBSCRIBE from vectorlist, send a message with
> > > > > "UNSUBSCRIBE" in the
> > > > > ** message body to vectorlist-request@synthcom.com. Please
> > > direct other
> > > > > ** questions, comments, or problems to
> > vectorlist-owner@synthcom.com.
> > > >
> > > >
> > >
> >
> ------------------------------------------------------------------------
> --
> > > -
> > > > ** To UNSUBSCRIBE from vectorlist, send a message with
> > "UNSUBSCRIBE" in
> > > the
> > > > ** message body to vectorlist-request@synthcom.com. Please
> > direct other
> > > > ** questions, comments, or problems to
> vectorlist-owner@synthcom.com.
> > >
> > > ------------------------------------------------------------------
> > > ---------
> > > ** To UNSUBSCRIBE from vectorlist, send a message with
> > > "UNSUBSCRIBE" in the
> > > ** message body to vectorlist-request@synthcom.com. Please direct
> other
> > > ** questions, comments, or problems to
> vectorlist-owner@synthcom.com.
> >
> > ------------------------------------------------------------------
> > ---------
> > ** To UNSUBSCRIBE from vectorlist, send a message with
> > "UNSUBSCRIBE" in the
> > ** message body to vectorlist-request@synthcom.com. Please direct
> other
> > ** questions, comments, or problems to vectorlist-owner@synthcom.com.
>
> ------------------------------------------------------------------------
> ---
> ** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in
> the
> ** message body to vectorlist-request@synthcom.com. Please direct other
> ** questions, comments, or problems to vectorlist-owner@synthcom.com.
>
> ------------------------------------------------------------------
> ---------
> ** To UNSUBSCRIBE from vectorlist, send a message with
> "UNSUBSCRIBE" in the
> ** message body to vectorlist-request@synthcom.com. Please direct other
> ** questions, comments, or problems to vectorlist-owner@synthcom.com.

---------------------------------------------------------------------------
** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
** message body to vectorlist-request@synthcom.com. Please direct other
** questions, comments, or problems to vectorlist-owner@synthcom.com.
Received on Fri Apr 4 17:02:10 2003