RE: Tempest lines fading

From: Joe <jb_at_joesarcade.com>
Date: Tue Aug 26 2003 - 23:00:47 EDT

Here's 2 short movies I took of it.. It is not the monitor. I connected
this to my 25" amp to take the movie.

www.joesarcade.com/temp1.mov
www.joesarcade.com/temp2.mov

Any suggestions are welcomed.

Thanks,
JB

-----Original Message-----
From: Joe
Sent: Tuesday, August 26, 2003 8:32 PM
To: vectorlist@vectorlist.org
Subject: RE: VECTOR: Tempest lines fading

Yes. This is not the monitor. SEVERAL other boards work just fine with
this monitor... This is just a problem with one or two boards.... I'll
try to get some pics...

JB

-----Original Message-----
From: Andy Welburn [mailto:andy@andys-arcade.com]
Sent: Tuesday, August 26, 2003 7:02 PM
To: vectorlist@vectorlist.org
Subject: Re: VECTOR: Tempest lines fading

I'm maybe not up to speed on this one, have you tried the pcb with a
different monitor or vice versa ?

I have come across temperamental blanking Z circuits in G05's and 6100's
before, usually its down to a transistor breaking down under load in the
Z
section on the monitor... very hard to spot as the transistors checked
good
out of circuit on my meter (fluke 12 that can spot leakage).

I also had a similar problem with a battlezone pcb that would trip the Z
circuit on the G05 infrequently.. I didn't suspect the pcb until i got
another G05 which did the same thing and realised it was the pcb not the
monitor... the battlezone AVG section 'crops' the picture so that it
doesn't
display a super widescreen version, and instead makes it 4:3 for the
monitor
(yes thats a simplified rendition of what it actually does).. what was
happening in my case was the picture wasn't being cropped, so even
though
the game played perfectly, it was displaying the mountains way off the
side
of the tube, therefore giving the Z section on the monitor a headache as
it
wasn't sure if it should kill the beam or not. This probably doesn't
apply
to tempest as there are no conceivably huge landscapes involved....

Maybe that doesn't help, but try shotgunning the Z on the monitor, a
handful
of 2n3906's and some MPSA56's i think should do the trick. It just
sounds
odd that it would be the same problem on 2 pcbs...

Andy Welburn
www.andys-arcade.com

----- Original Message -----
From: "Joe" <jb@joesarcade.com>
To: <vectorlist@vectorlist.org>
Sent: Tuesday, August 26, 2003 4:02 PM
Subject: VECTOR: Tempest lines fading

> I have two Tempest boards here in which the vectors fade in and out.
On
> the one board, I notice it most on the horizontal vectors. They start
> off as a normal width, but will change to about half the width. When
> faded, zeros on the screen look more like ones. Do, a high score of
> 1010101 would look like ||||||||||, but with VERY faint lines
connecting
> the tops and bottoms.
>
> I've been concentrating on the DAC-08 area, but I feel I may be
chasing
> a red herring here... I know this is not related to the aux board. Any
> suggestions?
>
> Thanks,
> JB
>
>
------------------------------------------------------------------------

--
-
> ** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE"
in
the
> ** message body to vectorlist-request@vectorlist.org. Please direct
other
> ** questions, comments, or problems to chris@westnet.com .
>
------------------------------------------------------------------------
---
** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in
the
** message body to vectorlist-request@vectorlist.org. Please direct
other
** questions, comments, or problems to chris@westnet.com .
------------------------------------------------------------------------
---
** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in
the
** message body to vectorlist-request@vectorlist.org. Please direct
other
** questions, comments, or problems to chris@westnet.com .
---------------------------------------------------------------------------
** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
** message body to vectorlist-request@vectorlist.org. Please direct other
** questions, comments, or problems to chris@westnet.com .
Received on Tue Aug 26 22:33:04 2003

This archive was generated by hypermail 2.1.8 : Thu Aug 28 2003 - 22:50:00 EDT