RE: Tech: Battlezone

From: Joe <jb_at_joesarcade.com>
Date: Wed Apr 30 2003 - 04:28:29 EDT

Marlin,

A meltdown is always bad. Start by disconnecting the HV cage. Check the
glow. Check the voltage to the heater.

There is no replacement HVT, but they are available. I have several
extra.

JB

-----Original Message-----
From: Marlin Bates, IV [mailto:mcb242@psu.edu]
Sent: Wednesday, April 30, 2003 2:08 AM
To: vectorlist@synthcom.com
Subject: Re: VECTOR: Tech: Battlezone

That's the thing, the monitor USED to get a neck glow and then a bad
ARII board took out a PROM (from the Aux board) and, I think, the HV
Board. The connector INISDE the HV cage looks VERY melted.

Does this mean new HV/Flyback or new Tube? If so, where do I get one
of those?

Thanks for the help.

-Marlin

On Tuesday, April 29, 2003, at 10:54 PM, Joe wrote:

> Marlin,
>
> First thing is the glow in the neck. Is the heater getting 6.3v? Check
> and resolder the headers on the deflection board. Even if they look
> good, they may need resoldering. After this. Check your 6.3v. If you
> are
> not getting 6.3v be sure that you are getting the heater voltage into
> the monitor. If you are getting 6.3v to the heater, it may be time to
> consider a new tube (not likely.)
>
> Also, are you getting HV?
>
> JB
>
> -----Original Message-----
> From: Marlin Bates, IV [mailto:mcb242@psu.edu]
> Sent: Tuesday, April 29, 2003 11:40 PM
> To: vectorlist@synthcom.com
> Subject: VECTOR: Tech: Battlezone
>
> Hello folks,
>
> I need some help. I think I know the answer, but figured I would ask
> to make sure.
>
> I have a Battlezone that I have replaced the AR II Board, the Game
> boards, and the main P/s with a known working unit(s). Now, I have a
> game which seems to coin up, and 'play' but no image on the monitor.
> There seems to be neck chatter BUT there is no neck glow. Spot killer
> lamp seems to go off until I coin-up and then it comes on.
>
> Thanks for the help.
>
> -Marlin
>
>
-----------------------------------------------------------------------
> -
> ---
> ** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE"
in
> the
> ** message body to vectorlist-request@synthcom.com. Please direct
other
> ** questions, comments, or problems to vectorlist-owner@synthcom.com.
>
>
-----------------------------------------------------------------------
> ----
> ** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE"
> in the
> ** message body to vectorlist-request@synthcom.com. Please direct
other
> ** questions, comments, or problems to vectorlist-owner@synthcom.com.
>

------------------------------------------------------------------------

---
** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in
the
** message body to vectorlist-request@synthcom.com. Please direct other
** questions, comments, or problems to vectorlist-owner@synthcom.com.
---------------------------------------------------------------------------
** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
** message body to vectorlist-request@synthcom.com. Please direct other
** questions, comments, or problems to vectorlist-owner@synthcom.com.
Received on Wed Apr 30 01:09:12 2003

This archive was generated by hypermail 2.1.8 : Fri Aug 01 2003 - 00:34:28 EDT